300W LED Fresnel Light | CRI 97 COB | SANYI LIGHTS
+1 626-408-8003

California, USA

15% OFF

STUDIO LUX FN400

SY-FN400

Ra 97 300W glass Fresnel with four switchable sources (3200K, 5600K, dual, RGBW) and a 10°–65° motorized zoom.

$768.00

✔
Four Light Sources In One Fixture3200K / 5600K / Dual / RGBW
Tungsten, daylight, blended white and full color without swapping heads
✔
Glass Fresnel, 10°–65° ZoomMotorized
Go from a tight 10° pool to a 65° flood from the console
✔
34,800 / 37,600 lm Output123 / 133 lm/W
Measured photometric output at both color temperatures, not a chip rating
✔
16-Bit Flicker-Free DimmingCamera Safe
Linear 0–100% dimming that broadcast and film cameras will not see strobing
✔
Copper-Pipe Air CoolingBarn Doors Included
Quiet enough to work in the same room as an open microphone
In stock · Ships within 1-2 business days

Checkout safely using your preferred payment method

From:

$768.00

Main Features

A 300W glass-Fresnel COB with CRI up to 97, four switchable light sources (3200K / 5600K / dual / RGBW) and a motorized 10°–65° zoom — broadcast-grade color at $768 a fixture.

Color Cameras Actually Trust

The FN400 runs an imported integrated COB with CRI Ra ≥ 90 and up to 97, so skin tones and fabric colors land where the camera expects them instead of drifting warm or green. Output reaches 34,800 lm at 3200K and 37,600 lm at 5600K, with efficacy up to 133 lm/W. For interview setups, product shots and broadcast work, that combination means less time in the grade and fewer gel corrections on set.

Tungsten, Daylight, Dual And RGBW In One Body

Four light-source modes live in the same fixture: 3200K for a tungsten look, 5600K for daylight, a dual-color mix for any point between the two, and full RGBW when the scene needs color. One FN400 can stand in for a tungsten fresnel on set, a daylight unit by a window, and a color wash for a stage moment — which is three fewer fixtures to buy, store and truck.

A Fresnel Beam You Can Zoom From The Console

The glass Fresnel lens with motorized 10°–65° zoom gives you the classic soft-edged fresnel beam with console-controlled spread: a wide gentle pool for a two-shot, then a tight accent on a single performer without touching the fixture. Manual focus is there when you are working alone with no desk, so the FN400 fits both a broadcast gallery and a one-person corporate shoot.

16-Bit Flicker-Free Dimming For Camera

Dimming is 0–100% linear at 16-bit resolution and flicker-free, which is what keeps slow-motion and high-frame-rate footage clean instead of showing rolling banding on every fade. The electronic strobe adds 1–30 flashes per second when a scene calls for it, so the same fixture covers the moody music-video moment and the straight-on corporate headshot.

Quiet Cooling, Long Life

Copper-pipe air cooling keeps fan noise to a whisper, which is the difference between a usable light and a distraction in broadcast studios, theatres and quiet interview sets. The LED engine is rated for 50,000–100,000 hours, so the fixture is built for years of daily service rather than a season of shoots.

Simple 5-Channel Control

A single 5-channel DMX mode — Focus, Speed, Dimmer, Strobe and Function — keeps patching and programming short. There is no hidden personality to hunt for: five channels cover spread, fade, strobe and mode, which means a volunteer or a first-time operator can run the FN400 from a small console without a manual open on the desk.

Ready To Hang Out Of The Box

The aluminum body with black epoxy coating ships with rotating barn doors, a signal cable and a power cable — everything needed to mount, focus and go, with no separate accessory order. At $768 for the single-fixture package, a two- or three-light interview kit costs a fraction of a comparable broadcast fresnel.

WHO IT’S BUILT FOR

TV, film and streaming studios
High CRI with flicker-free 16-bit dimming is exactly what a camera department asks for, and the four light-source modes mean one inventory item covers tungsten sets, daylight windows and color sequences. The 5-channel mode keeps a studio patch tidy when several fixtures hang on the same grid.
Photography and content studios
Accurate skin tones at CRI up to 97, a soft fresnel edge that flatters faces, and a 10°–65° zoom that covers a full-length portrait or a tight product detail. At 300W with 34,800–37,600 lm it is bright enough for a softbox-free setup, and the barn doors ship in the box for quick shaping.
Theatres and houses of worship
A quiet copper-pipe cooling system matters when the room goes silent, and the motorized zoom lets the lighting volunteer reframe a scene from the desk instead of a ladder. 3200K warms a stage wash while 5600K matches a video feed, so the same fixtures serve both the live room and the stream.
Corporate stages and event production
One fixture per position covers tungsten key, daylight fill and color accent, which simplifies both the quote and the load-in. Manual focus means a single operator can set the beam before the desk is patched, and the rotating barn doors control spill on tight ballroom ceilings.
Indoor use only
The STUDIO LUX FN400 is a studio and stage fixture with no weather rating, so keep it in covered, dry spaces — studios, stages, theatres and houses of worship. For outdoor or weather-exposed events, choose an IP65-rated fixture from our outdoor range instead.

FREQUENTLY ASKED QUESTIONS

What makes the STUDIO LUX FN400 different from a standard 300W fresnel?
Color and control. CRI runs Ra ≥ 90 and up to 97, so it is built for camera work rather than only for the eye. It also carries four light-source modes — 3200K, 5600K, a dual-color mix and full RGBW — plus a motorized 10°–65° zoom, where a standard fresnel is one color temperature with a hand-set beam.
How many FN400 fixtures do I need?
One is enough for a single-subject interview or a product setup. Two gives you a key and a fill with independent dimming, and three covers a key/fill/backlight triangle for a two-person shot. At $768 each for the 1 PC package, a three-light kit costs less than a single comparable broadcast fresnel.
Do I need a DMX controller to run it?
No. The beam can be focused by hand on the fixture, so the FN400 works as a standalone light. Patch a console and you gain direct control of Focus, Speed, Dimmer, Strobe and Function over the 5-channel DMX mode, including console-driven motorized zoom.
What do the four light-source modes actually give me?
3200K matches tungsten practicals and warm interiors, 5600K matches daylight and most video cameras, the dual-color mix lets you dial any point between the two, and RGBW opens full color for music, stage and stylised looks. It means one fixture covers the looks that would otherwise need three separate lights.
Can I use it outdoors?
No. The FN400 is built for indoor use — studios, stages, theatres and covered venues. For outdoor or weather-exposed events, choose an IP65-rated fixture from our outdoor range instead.
How is it powered, and what comes in the box?
It runs on AC 100–240V, 50/60Hz with a 300W power consumption, so it works on US and European mains. Each fixture ships with rotating barn doors, a signal cable and a power cable, plus free USA shipping on most products, a 2-year warranty and a 30-day return policy.
Will it hold up to daily studio work?
Yes. The LED engine is rated for 50,000–100,000 hours, so even five hours of use a day is measured in decades rather than years. Copper-pipe air cooling keeps the engine and fan noise under control at the same time, which is what makes it viable in a live broadcast booth.

Everything you need for the STUDIO LUX FN400
The user manual, the technical specification sheet and the DMX fixture profile for the FN400 — one folder, three files.
USER'S MANUAL  ·  TECHNICAL SPECIFICATIONS  ·  FIXTURE'S PROFILE
Building a full rig?
The Download Center holds every SANYI LIGHTS fixture profile in one place — grab the whole set instead of one by one.
Open the Download Center →

Free shipping on most products across the USA — plus a 2-year warranty and a 30-day return policy on every order.

Designed for Creators.

Built for the Stage.

High Output

Performance

RGBW Color 

System

DMX & Wireless
Control

Venue-Ready

Build

Plug & Play 

Simplicity

Overview

This compact and powerful fixture is engineered for performers who demand precision and impact. With crystal-clear output, seamless wireless control and reliable DMX integration, it’s the go-to lighting solution for professionals on the move.

Perfect For

Overview

This compact and powerful fixture is engineered for performers who demand precision and impact. With crystal-clear output, seamless wireless control and reliable DMX integration, it’s the go-to lighting solution for professionals on the move.

Creator insinght

customer reviews

Overview

This compact and powerful fixture is engineered for performers who demand precision and impact. With crystal-clear output, seamless wireless control and reliable DMX integration, it’s the go-to lighting solution for professionals on the move.

Creator Insight

Customer
Reviews

Specifications & Features

Main Features

A 300W glass-Fresnel COB with CRI up to 97, four switchable light sources (3200K / 5600K / dual / RGBW) and a motorized 10°–65° zoom — broadcast-grade color at $768 a fixture.

Color Cameras Actually Trust

The FN400 runs an imported integrated COB with CRI Ra ≥ 90 and up to 97, so skin tones and fabric colors land where the camera expects them instead of drifting warm or green. Output reaches 34,800 lm at 3200K and 37,600 lm at 5600K, with efficacy up to 133 lm/W. For interview setups, product shots and broadcast work, that combination means less time in the grade and fewer gel corrections on set.

Tungsten, Daylight, Dual And RGBW In One Body

Four light-source modes live in the same fixture: 3200K for a tungsten look, 5600K for daylight, a dual-color mix for any point between the two, and full RGBW when the scene needs color. One FN400 can stand in for a tungsten fresnel on set, a daylight unit by a window, and a color wash for a stage moment — which is three fewer fixtures to buy, store and truck.

A Fresnel Beam You Can Zoom From The Console

The glass Fresnel lens with motorized 10°–65° zoom gives you the classic soft-edged fresnel beam with console-controlled spread: a wide gentle pool for a two-shot, then a tight accent on a single performer without touching the fixture. Manual focus is there when you are working alone with no desk, so the FN400 fits both a broadcast gallery and a one-person corporate shoot.

16-Bit Flicker-Free Dimming For Camera

Dimming is 0–100% linear at 16-bit resolution and flicker-free, which is what keeps slow-motion and high-frame-rate footage clean instead of showing rolling banding on every fade. The electronic strobe adds 1–30 flashes per second when a scene calls for it, so the same fixture covers the moody music-video moment and the straight-on corporate headshot.

Quiet Cooling, Long Life

Copper-pipe air cooling keeps fan noise to a whisper, which is the difference between a usable light and a distraction in broadcast studios, theatres and quiet interview sets. The LED engine is rated for 50,000–100,000 hours, so the fixture is built for years of daily service rather than a season of shoots.

Simple 5-Channel Control

A single 5-channel DMX mode — Focus, Speed, Dimmer, Strobe and Function — keeps patching and programming short. There is no hidden personality to hunt for: five channels cover spread, fade, strobe and mode, which means a volunteer or a first-time operator can run the FN400 from a small console without a manual open on the desk.

Ready To Hang Out Of The Box

The aluminum body with black epoxy coating ships with rotating barn doors, a signal cable and a power cable — everything needed to mount, focus and go, with no separate accessory order. At $768 for the single-fixture package, a two- or three-light interview kit costs a fraction of a comparable broadcast fresnel.

WHO IT’S BUILT FOR

TV, film and streaming studios
High CRI with flicker-free 16-bit dimming is exactly what a camera department asks for, and the four light-source modes mean one inventory item covers tungsten sets, daylight windows and color sequences. The 5-channel mode keeps a studio patch tidy when several fixtures hang on the same grid.
Photography and content studios
Accurate skin tones at CRI up to 97, a soft fresnel edge that flatters faces, and a 10°–65° zoom that covers a full-length portrait or a tight product detail. At 300W with 34,800–37,600 lm it is bright enough for a softbox-free setup, and the barn doors ship in the box for quick shaping.
Theatres and houses of worship
A quiet copper-pipe cooling system matters when the room goes silent, and the motorized zoom lets the lighting volunteer reframe a scene from the desk instead of a ladder. 3200K warms a stage wash while 5600K matches a video feed, so the same fixtures serve both the live room and the stream.
Corporate stages and event production
One fixture per position covers tungsten key, daylight fill and color accent, which simplifies both the quote and the load-in. Manual focus means a single operator can set the beam before the desk is patched, and the rotating barn doors control spill on tight ballroom ceilings.
Indoor use only
The STUDIO LUX FN400 is a studio and stage fixture with no weather rating, so keep it in covered, dry spaces — studios, stages, theatres and houses of worship. For outdoor or weather-exposed events, choose an IP65-rated fixture from our outdoor range instead.

FREQUENTLY ASKED QUESTIONS

What makes the STUDIO LUX FN400 different from a standard 300W fresnel?
Color and control. CRI runs Ra ≥ 90 and up to 97, so it is built for camera work rather than only for the eye. It also carries four light-source modes — 3200K, 5600K, a dual-color mix and full RGBW — plus a motorized 10°–65° zoom, where a standard fresnel is one color temperature with a hand-set beam.
How many FN400 fixtures do I need?
One is enough for a single-subject interview or a product setup. Two gives you a key and a fill with independent dimming, and three covers a key/fill/backlight triangle for a two-person shot. At $768 each for the 1 PC package, a three-light kit costs less than a single comparable broadcast fresnel.
Do I need a DMX controller to run it?
No. The beam can be focused by hand on the fixture, so the FN400 works as a standalone light. Patch a console and you gain direct control of Focus, Speed, Dimmer, Strobe and Function over the 5-channel DMX mode, including console-driven motorized zoom.
What do the four light-source modes actually give me?
3200K matches tungsten practicals and warm interiors, 5600K matches daylight and most video cameras, the dual-color mix lets you dial any point between the two, and RGBW opens full color for music, stage and stylised looks. It means one fixture covers the looks that would otherwise need three separate lights.
Can I use it outdoors?
No. The FN400 is built for indoor use — studios, stages, theatres and covered venues. For outdoor or weather-exposed events, choose an IP65-rated fixture from our outdoor range instead.
How is it powered, and what comes in the box?
It runs on AC 100–240V, 50/60Hz with a 300W power consumption, so it works on US and European mains. Each fixture ships with rotating barn doors, a signal cable and a power cable, plus free USA shipping on most products, a 2-year warranty and a 30-day return policy.
Will it hold up to daily studio work?
Yes. The LED engine is rated for 50,000–100,000 hours, so even five hours of use a day is measured in decades rather than years. Copper-pipe air cooling keeps the engine and fan noise under control at the same time, which is what makes it viable in a live broadcast booth.

Technical Specification — SY-FN400

Full factory specification for the STUDIO LUX FN400 (SY-FN400). All four light-source modes and the motorized 10°–65° zoom are built into the same fixture.
Electrical
Input powerAC 100–240V, 50/60Hz
Power consumption300W
Voltage rangeUniversal — works on US and EU mains
Light Source
LEDImported integrated COB, 300W
Color modes3200K / 5600K / 3200K+5600K / full-color RGBW
Luminous flux34,800 lm (3200K) / 37,600 lm (5600K)
Efficacy123 / 133 lm/W
CRIRa ≥ 90 (up to 97)
Average lifespan50,000–100,000 hours
Optics
LensGlass Fresnel
Beam angle10°–65° (motorized via DMX or manual focus)
Dimming & Strobe
Dimming0–100% linear, 16-bit flicker-free
StrobeElectronic, 1–30 flashes/sec
Control
ProtocolDMX512
DMX channels5 CH (Focus / Speed / Dimmer / Strobe / Function)
Cooling & Housing
CoolingUltra-quiet copper-pipe air cooling
HousingAluminum, black epoxy coating
Physical
AccessoriesRotating barn doors, signal cable, power cable
Everything you need for the STUDIO LUX FN400
The user manual, the technical specification sheet and the DMX fixture profile for the FN400 — one folder, three files.
USER'S MANUAL  ·  TECHNICAL SPECIFICATIONS  ·  FIXTURE'S PROFILE
Building a full rig?
The Download Center holds every SANYI LIGHTS fixture profile in one place — grab the whole set instead of one by one.
Open the Download Center →

Reviews

Be the first to review “STUDIO LUX FN400”

Your email address will not be published. Your review will show your first name and the first letter of your last name — for example “John D.”

Reviews

Designed for Creators.

Built for the Stage.

High Output

Performance

RGBW Color 

System

DMX & Wireless
Control

Venue-Ready

Build

Plug & Play 

Simplicity

Overview

This compact and powerful fixture is engineered for performers who demand precision and impact. With crystal-clear output, seamless wireless control and reliable DMX integration, it’s the go-to lighting solution for professionals on the move.

Creator Insight

Customer
Reviews

You May Also Like

10% OFF
VERSATILIS 300BSW front view - black moving head, lens, yoke, base control panel, buttons, display

VERSATILIS 300BSW

HYBRID 300W LED beam, spot and wash moving head with a 4°–34°…
From: Original price was: $1,999.00. Current price is: $1,899.00.
Buy Now
10% OFF
STUDIO LUX LK300 three-quarter view - black cylindrical spotlight body, yoke bracket, front lens, cooling vents

STUDIO LUX LK300

AUTO-FOCUS 300W dual-color COB profile with 2700K–7500K tuning, Ra ≥ 95 up…
From: $953.00
Buy Now
10% OFF
STUDIO LUX FN400 front view - black, open barn doors, textured glass lens, wire frame

STUDIO LUX FN400

Ra 97 300W glass Fresnel with four switchable sources (3200K, 5600K, dual,…
From: $768.00
Buy Now
10% OFF
PULSARIS BAR 720B IP front view - long black light bar, square LED grid, two mounting brackets, eyelets

PULSARIS BAR 720B IP

IP65 outdoor linear pixel bar with 504 × 0.3W RGB and 122…
From: From $475.00
Buy Now
10% OFF
COLOR SPECTRUM TUBE front view - vertical white light tube, black base, control panel, two buttons, stand

COLOR SPECTRUM TUBE

BATTERY 40W RGBWA linear tube with 32 pixels, a 9600mAh cell for…
From: $1,480.00
Buy Now
10% OFF
HUEWAVE 19Z PAR front view - black round, circular array of LED lenses, U-shaped mounting bracket, ribbed housing edge

HUEWAVE 19Z PAR

19 × 15W motorized zoom RGBW PAR bringing a 10°–60° beam, 3-segment…
From: From $165.00
Buy Now
10% OFF
DUALTONE 200ZM three-quarter view - black, circular lens, U-bracket, adjustment knob, ridged housing

DUALTONE 200ZM

3200K–6000K 200W Citizen COB dual-color fixture mixing warm and cool white, with…
From: From $241.00
Buy Now
10% OFF
CYCLONE 80IP three-quarter view - black moving head, rainbow LED lens ring, yoke, base, control panel

CYCLONE 80IP

IP65 infinite pan and tilt beam with an 80W white LED at…
From: $2,499.00
Buy Now
10% OFF
HUEWAVE UPLIGHT BAR9(6PCS&1ROAD CASE) three-quarter view - black linear LED bar, nine purple illuminated lenses

HUEWAVE UPLIGHT BAR9(6PCS&1ROAD CASE)

IP65 six cordless RGBWA-UV uplight bars with one road case that charges…
From: $2,840.00
Buy Now
10% OFF
GOLDEN SPARKS X1 rear view - rear panel: fan, LEDs, LCD, buttons, switch, fuse, DMX/power ports

GOLDEN SPARKS X1

COLD SPARK 650W fountain spark machine throwing 9.8–16.4 ft with no open…
From: Original price was: $399.00.Current price is: $299.00.
Buy Now